1967-1968 Mustang E Body Kit Fastback aka Eleanor Includes: your choice of hood (six styles), upper nose (1 piece), lower nose, front fender flares, side exhaust skirts, rear fender flares, lower side scoops, upper side scoops and a spoiler trunk w/end caps. Upper and Lower billet grills available sold separately. E Kit Installation Guide This item is special order average 2 week build time. Fit, prep and finishing required. These are not simple bolt on parts. All parts are fiberglass unless noted otherwise.
Mustang Depot has sold more “E” Body Kits than any other retailer in the world! We offer more components, and a better insight to complete your Eleanor conversion than anyone! We can provide installation assistance if needed. Don’t go with the imitation kits, go with the one that has been around and survived the test of countless installs from our customers as seen in our Eleanor Photo gallery
This is a third generation kit, Gen.1 Cinema Vehicle Services, Gen. 2 Maier Racing, Gen. 3 FSI. Yes this is the kit you are purchasing.
DISCLAIMER: The word “Eleanor” has two registered trademarks, one owned by Carroll Shelby in the automotive classification, and the other by Denice Halicki in video games and toys. “Gone in 60 Seconds” is a registered trademark of Denice Halicki. GT-500 and GT-500E are also registered trademarks of Carroll Shelby. Mustang Depot has no affiliation with either Carroll Shelby, Denice Halicki of Gone in 60 Seconds, or Ford Motor Company. The terms “Eleanor” and “Mustang” when used, are used for descriptive purposes only and are not meant to imply any affiliation with their mark holders. Mustang Depot was one of the original distributors of the Eleanor Body Kit offered by Cinema Vehicle Services. We have since continued without interruption with the sales of these kits, and the use of the word “Eleanor” prior to both Carroll Shelby and Denice Halicki registering their marks. The styling of the Eleanor car from the motion picture Gone in 60 Seconds is based on a 1967 Shelby Mustang with some slight modifications. So the styling is considered public domain and is not and cannot be patented. Mustang Depot is not involved in the manufacturing of these body kits, or the manufacturing of replica cars. The kit on this page is sold as an “E2 Body Kit” not an Eleanor Kit out of respect for the mark holders. 1965, 1966. For off road use only..
Fiberglass body parts do not fit the same as stamped steel parts. While they can be finished to show quality, fiberglass body parts are built closer to race car standards than show car standards. Although fiberglass parts are easy to work with, they can require substantial work to conform to the varying early unibody Mustangs. This means every car is slightly different. We have come to this conclusion after many years of installing and selling fiberglass body parts from many different manufacturers. Within 60 days of receipt, you must check fit before sanding or painting your new fiberglass pieces. If fiberglass parts have been sanded or painted they can no longer be sold as new for either race or show purposes. For this reason, the manufacturer will not warranty such parts and cannot be accepted for a return. Our policy for returning fiberglass parts is subject to a 15% restocking fee. In the event you feel the product is defective, our policy requires that you send the product back to us fully insured, heavily packaged to avoid damages and freight prepaid. A full investigation by Mustang Depot and the manufacturer will ensue. This includes fitting the item on the respective car, matching the part to the mold, and matching it with other items produced from the same mold. If it is determined that the product is not defective and is in reasonable constraints for finishing, the product will be returned at the customers expense. If it is deemed that the product is defective, a replacement will be sent at no cost and the return freight charges incurred by the customer will be refunded in the form of an in-store credit. All product that leaves Mustang Depot is inspected and confirmed to be in good condition, heavily packaged, and is insured for the value of the product. Noted on the package are clear neon stickers warning you to inspect the product in the presence of the carrier/driver. In the event damages occur, have the driver notate the damage on the documentation before signing. If the package was left at your door, you must notify the carrier immediately and file a damage claim. Do not return the product to Mustang Depot it is our policy to refuse items without a Return Authorization number. Retain all the packaging so the carrier can inspect the product. In most cases, small repairs can be made at a reasonable cost. Get an estimate, and submit the claim. Full loss claims are scrutinized much heavier. Please note: For fiberglass hoods, removal of stock hood springs and use of a prop rod and hood pins are highly recommended. For trunks, removal of springs or tension rods is highly suggested. Fiberglass has about a 6-8 week cure time when it comes out of the molds. So it’s important to remove the parts from it’s packaging upon receipt. Do not place anything on top of the part during storage. The part will attempt to take the shape of whatever it’s stored on top of as well. Especially in warmer climates. The best place to store the part is on the car in it’s intended position. This kit is intended for off-road use only.